Wiha Single-pole, non-contact voltage tester volt detector, explosion protected 12-1,000 VAC incl. 2x AAA batteries (44309)
1x Inserto Standard 25 mm Phillips, 1/4"" C6,3 PH1 (01657)
Wiha Single-pole, non-contact voltage tester volt detector, explosion protected 12-1,000 VAC incl. 2x AAA batteries (44309)
1x Inserto Standard 25 mm Phillips, 1/4"" C6,3 PH1 (01657)
As low as
€56.50
excl. vat
In stock
Only %1 left
Shipped in 7-10 working days

Guaranteed,
certified quality
certified quality

Electronic invoicing
Technical description
Increased Efficiency: Built-in high-brightness LED flashlight
Time saving: Quick voltage check thanks to non-contact measurement
Increase your flexibility: The voltage tester covers a wide voltage range from 12 to 1000 V AC
Increased efficiency: Can be used worldwide thanks to measuring tip suitable for all socket outlets worldwide
Before starting an electrical installation, electricians must verify that the working environment is voltage-free
To test alternating electric fields or to locate suspected sources of error, a phase tester is required
An initial indication of the absence of voltage can be obtained thanks to the optical and acoustic signal of the Wiha contactless phase tester
After switching on, the steady green LED indicates that the appliance is ready for use
When checking the voltage, the LEDs light up from blue (weak) to orange to red (strong) depending on the strength of the alternating electric field
Two AAA batteries are required for use and are supplied
If the tester is not used for more than 4 minutes, it switches off automatically to save energy
An integrated LED torch allows the measurement points to be illuminated in dark environments and can also be used as a torch by manual switching on and off
Thanks to its handy size, the phase detector with clip easily fits into every shirt and trouser pocket
Thanks to the suitable measuring tip for all socket variants, the phase tester can be used worldwide
The single-phase voltage tester is subject to EN 61010-1 / IEC 61326 and is designed for CAT IV 1000 V AC
In addition, the tool is approved according to ATEX for potentially explosive areas (Category II)
Before and after each use, test the voltage tester with a known voltage source to ensure proper operation
Need any help?
Contact us for further information.
RELATED PRODUCTS
-
Wiha Stripping and assembly tool for coaxial cable with F-connector 125 mm (44241)As low as €29.30 excl. vat
-
Wiha Setting tool for torque screwdriver with T-handle 90 mm (28691)As low as €17.00 excl. vat
-
Wiha XLSelector T bit set, 50 mm Phillips, TORX®, hex 14-pcs. 1/4" E6,3 (41831)As low as €50.10 excl. vat
-
Wiha Ring ratchet open-ended spanner set 13 pcs. switchable, with holder (44661)As low as €176.70 excl. vat
-
Wiha Interchangeable blade Hexagon for torque screwdriver with key handle 1.5 mm (38801)As low as €7.00 excl. vat
-
Wiha Screwdriver with bit magazine magnetic TORX® with 6 bits, Stubby, 1/4" (33744)As low as €16.10 excl. vat
-
Wiha Screwdriver with bit magazine LiftUp electric TORX® with 6 slimBits (41158)As low as €67.70 excl. vat
-
Wiha Fine screwdriver set PicoFinish® slimVario® electric 4-pcs. with slimBits (43167)As low as €41.50 excl. vat
-
Wiha Screwdriver set SoftFinish® electric Slotted, Phillips 7-pcs. (00834)As low as €49.30 excl. vat
-
Wiha Interchangeable blade TORX® for torque screwdriver with T-handle T15 (28734)As low as €11.00 excl. vat